Jaroslav Kysela [Tue, 5 Nov 2019 19:09:21 +0000 (20:09 +0100)]
sof-hda-dsp: adapt to latest alsa-lib
- move to ucm2
- add 'Syntax 2' to the main configuration files
- use condition for 'Headphone Jack' / 'Headphone Mic Jack' selection
- remove cdev (not required)
- use ${CardId} where appropriate
- merge config for Lenovo Carbon X1 7th gen to main HiFi.conf
Jaska Uimonen [Fri, 25 Oct 2019 17:23:56 +0000 (20:23 +0300)]
sof-skl_hda: move hdmi as separate use case
Move hdmi definitions as separate use case and conf file. This will
enable Pulseaudio to create separate profile for hdmi and make routing
much more fluent than with single profile.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sof-skl_hda: add PlaybackVolume and CaptureVolume definitions
PlaybackVolume and CaptureVolume are not defined currently and these are
needed in the future for example with Pulseaudio to enable hardware
volume control.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sof-skl_hda: remove volume setting in enable/disable sequences
If the volume setting is defined in enable sequence you will
always get that exact volume when switching outputs in some
user space software like Pulseaudio. Pulseaudio will itself
keep track of the volume previously set.
Jaroslav Kysela [Tue, 24 Sep 2019 11:39:14 +0000 (13:39 +0200)]
Add initial support for generic SOF Skylake driver (DMIC)
Based on: https://github.com/RanderWang/intel-UCM/tree/hdmi/sof-skl_hda_card Signed-off-by: Mark Pearson <mpearson@lenovo.com>
Cleanups, remove commented or empty configuration.
Hans de Goede [Sat, 31 Aug 2019 14:58:41 +0000 (16:58 +0200)]
conf/ucm: Add UCM profile for cht-bsw-rt5672 boards
Add an UCM profile for Intel boards with a RT5672 codec.
Re-use the existing platform enable and disable sequences for BYT/CHT SST
support and add a codecs/rt5672 dir with codec specific enable / disable
sequences for the various inputs and outputs.
This is partly based on earlier work done here:
https://github.com/plbossart/UCM/tree/master/cht-bsw-rt5672
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Sun, 3 Feb 2019 11:37:41 +0000 (12:37 +0100)]
ucm: bytcr/PlatformEnableSeq.conf update some comments
Commit f91cc3c7d6b7 ("Update chtrt5645 ucm variants to use
bytcr/PlatformEnableSeq.conf component") updated the
following 2 comments:
# codec0_out settings (used if SSP2 is connected to aif1)
# modem_out settings (used if SSP0 is connected to aif2)
Specifically it added the " to aif1" resp. " to aif2" part of the comments.
This is not correct, AIF1 / AIF2 are something which is present on
Realtek codecs only, and either one can be used indepedent of
SSP0 or SSP2 being used (the comments in the chtrt5645 UCM profile
before this change were wrong / outdated).
Besides there not being any relationship between SSP0 or SSP2 being
used, bytcr/PlatformEnableSeq.conf is also used with other codecs,
e.g. the ESS8316 codec where this is not applicable at all.
Therefor this commit removes the " to aif?" part of the comments again
to avoid confusing people reading this in the future.
Cc: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
DB820c board is based of MSM8996 Qualcomm SoC, which has support for both
Digital and Analog audio. Digital audio is over HDMI and analog is over
WCD9335 codec via SLIMbus.
Board itself has HDMI port, a 3.5mm audio Jack and an Audio expansion
connector.
This patch adds support for HDMI port and 3.5mm jack.
Hui Wang [Tue, 27 Nov 2018 01:36:28 +0000 (09:36 +0800)]
conf/ucm: Add a UCM profile for Dell WD19 Dock USB-audio
USB-audio device on Dell WD19 docking station provides two individual
output PCM streams, one for headphone Jack and another for speaker out
Jack. A UCM profile gives the proper roles for these.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After recent kernel work, the kernel now sets a long-name for bytcht-es8316
boards which indicates if a single (mono) speaker or stereo speakers are
used and if in1 or in2 is used for the internal mic (the headset mic will
be on the other input).
This commit adds UCM profiles for bytcht-es8316 boards using these new
long-names, based on the generic bytcht-es8316 profile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Thu, 3 Jan 2019 13:50:14 +0000 (14:50 +0100)]
conf/ucm: Add UCM profile for bytcht-es8316 boards
Add an UCM profile for Bay Trail and Cherry Trail boards with an
ES8316 codec.
Re-use the existing platform enable and disable sequences for BYT/CHT SST
support and add a codecs/es8316 dir with codec specific enable / disable
sequences for the various inputs and outputs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Russell Parker [Sun, 6 Jan 2019 03:47:15 +0000 (19:47 -0800)]
Create device component for rt5645 Internal Analog Mic UCM
Since the Internal Analog Microphone device configuration is
identical for the rt5645 and rt5645 mono speaker UCMs, move
the entire definition to a component.
Signed-off-by: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Russell Parker [Sun, 6 Jan 2019 03:47:13 +0000 (19:47 -0800)]
Factor out rt5645 variants Speaker+Headphones shared UCM enable sequences
Move common enable sequences for rt5645 variants and rt5650
UCM configurations into a shared component. The corresponding
disable sequences are only two lines each and do not seem worth
creating components for.
Signed-off-by: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Russell Parker [Sun, 6 Jan 2019 03:47:12 +0000 (19:47 -0800)]
Create shared {En,Dis}ableSeq.conf components for rt5645 variants
Factor out the common enable and disable sequences used
in rt5645 variants, including the rt5650. Move the sequences
into a new component directory codecs/rt5645/ along with
a Makefile.
Some lines like
cset "name='Stereo1 ADC1 Mux' 1"
and
cset "name='I2S2 Func Switch' on"
are not set set in the chtrt5650 UCM sequences and thus are not present
in the new component, in order to maximize reuse.
Signed-off-by: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Russell Parker [Sun, 6 Jan 2019 03:47:11 +0000 (19:47 -0800)]
Update chtrt5645 ucm variants to use bytcr/PlatformEnableSeq.conf component
The Lenovo Ideapad Miix 320, Asus T100HA, and chtrt5645 mono variant
UCM configurations have not been updated to make use of the shared
bytcr/PlatfromEnableSeq.conf sequence. This commit deletes those
command sequences and loads the shared component directly.
Signed-off-by: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
During my recent work on the bytcht-es8316 UCM profile I realized that the
bytcr-rt5651 devices with a single speaker use a differential setup just
like the es8316 does. The tell-tale here is the speaker going quiet when
playing the exact same sound on both channels when things are configured
for stereo speakers.
I've run some tests and the rt5651 does have a special mono balanced out
mode for its line-out but using this results in the same sound (and the
same loudness / volume of the sound) as our current solution, so adding
support for this to the kernel buys us nothing.
This commit makes no changes, it just documents my findings in a big
comment for future reference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hui Wang [Mon, 24 Dec 2018 08:34:46 +0000 (16:34 +0800)]
conf/ucm: kblrt5660: Add ucm setting for Dell Edge IoT platform
The new generation of Dell Edge IoT platform is based on Intel
Kabylake platform, and the audio codec is ALC3277 which is 100%
compatible with RT5660 in I2S mode.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Russell Parker [Sun, 30 Dec 2018 05:35:26 +0000 (21:35 -0800)]
conf/ucm: chtrt5650: Add UCM config for chtrt5650
Add a UCM configuration for the rt5650 codec. Tested on
a Samsung Chromebook 3. Adapted with minor modifications
from GitHub user evan-a-a's gist:
https://gist.github.com/evan-a-a/86b2a698708074530e2d0ee7c6498767
Signed-off-by: Russell Parker <russell.parker7@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Wed, 28 Nov 2018 15:25:41 +0000 (16:25 +0100)]
ucm: Set default include path
Many UCM profiles include the UCM profile components under ucm/*
subdirectories and thusly put <searchdir:ucm> at each place. This is
rather cumbersome.
This patch makes the UCM parser to set the default include path, so
that each profile no longer needs to set searchdir. All the
<searchdir:ucm> lines currently found in the profiles are removed
gracefully, too.
For the needed implementation, a new helper,
_snd_config_load_with_include() is introduced. It's not exported,
only for the use inside alsa-lib.
Takashi Iwai [Tue, 27 Nov 2018 12:55:04 +0000 (13:55 +0100)]
conf: Move UCM profile snippets into components subdirectory
We have placed UCM profile snippets to be included by the main config
files also in the same directory, src/conf/ucm, it confuses alsaucm
program that scans over all subdirectories. It thinks such a file is
also the main config file, and spews errors like:
% alsaucm
ALSA lib utils.c:67:(uc_mgr_config_load) could not open configuration file /usr/share/alsa/ucm/bytcr/bytcr.conf
ALSA lib parser.c:1427:(load_master_config) error: could not parse configuration for card bytcr
alsaucm: unable to obtain card list: No such file or directory
Actually we already defined the subdirectory for such components, and
they are skipped at parsing the main configs. So we just need to move
the files there -- this is what's done here.
One more thing done here is to add a new component subdirectory,
platforms, for definitions bytcr/* that don't match with neither the
existing ones (codecs nor dsps).
Suggested-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jaroslav Kysela <perex@perex.cz> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hans de Goede [Wed, 8 Aug 2018 09:05:43 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5640: Improve human readable input/output names
The Comment field is displayed tot the end user in various UIs as such
names like MonoSpeaker and DigitalMics without any spaces are no good.
Also the names themselves as well as how they get displayed in the
typical UI (in separate input / output tabs) makes the adding of
playback and capture to the comment superfluous and this looks weird
in the UI, so drop it.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a longname profile for devices with a mono speaker, the Internal Mic
hooked up to IN2 and the left and right channels of their headphones
output swapped.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After recent kernel work, the kernel now sets a long-name for bytcr-rt5651
boards which indicates if a single (mono) speaker or stereo speakers are
used and if in1, in2, or in1 and 2 are used for the internal mic(s) (the
headset mic sofar is always on in3).
This commit adds UCM profiles for bytcr-rt5651 boards using these new
long-names, based on the generic bytcr-rt5651 profile.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Many rt5651 devices only have a single speaker and even though there is
some external mixing done on the PCB, the quality of that mixing is quite
poor and various sounds come out garbled when relying on the on PCB mixing.
Using the codecs builtin mixer to mix left + right to the left output works
much better. This commits adds a new MonoSpeaker.conf output profile which
allows this.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:39 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Split into 1 .conf file per input / output
Split the bytcr-rt5651 config into 1 .conf file per input / output as
has already been done for the bytcr-rt5640 and the chtnau8824 profiles.
This allows easy creation of long-name profiles with the specific input /
output combinations found on a board without needing to copy and paste
things.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:38 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Add support for mic input on various pins
Note this commit replaces the pre-existing "Handset Microphone" and
"Main Microphone" options, these come from the first commit of the
bytcr-rt5651 UCM profile and were based on wrong assumptions about the
input mappings. None of the existing devices has the Hand/Headset mic
on IN1 as these options assumed.
The rt5651 is used in various configurations with the Internal Mic(s)
hooked up to IN1, IN2, or to IN1 and IN2 and the Headset Mic hooked up
to IN3.
Add support for all these to the generic bytcr-rt5651 profile and name
them accotding to their input + functions.
A follow up commit will add specialized longname configs which
will only expose the inputs actually used on the board with that
longname.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:37 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Fix ADC and Mic capture volumes
Fix ADC and Mic capture volumes, so that the microphone inputs actually
work.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:36 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Use generic SSP enable + disable sequence, support SSP0
Use the generic SSP enable sequence from bytcr/PlatformEnableSeq.conf,
for boards using SSP2 this is identical the code it replaces and this
adds support for boards using SSP0.
This fixes sound not working on Bay Trail CR tablets with a rt5651 codec.
This commit also calls the generic disable sequence on shutdown
(this is new).
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:35 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Change Speaker/Headphone en/disable sequences to fix switching
pulseaudio will run the DisableSequence of the current playback device
before running the EnableSequence of the new playback device.
This causes the Platform Clock and BIAS to temporarily get turned off which
on the rt5651 breaks audio-streams which are playing when switching.
This commit moves the disabling to the EnableSequence of the other device
fixing this.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:34 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Start with all outputs and inputs disabled
Start with all switches disabled, so that e.g. the
LOUT L/R Playback Switches are not left enabled when starting with
headphones plugged in.
This fixes the platform clock being kept on by these in some cases.
While at also move the IN? Boost and IF1 ASRC Switch lines around
a bit to match the order from https://github.com/plbossart/UCM so
the profiles can be more easily compared.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
That commit also adds line-in support, so it has not been
taken in its entirety.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:32 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5651: Do not use both DAC1 and HPVOL inputs for HP
The headphones can either be driven directly from DAC1, or through
the HP volume mixer chain to allow volume control, both can be enabled
at the same time, but this should not be done.
Mix only DAC1 to the headphones and not the HP volume path, there
are 2 reasons to choice the DAC1 path;
1) It is the power-on-reset default
2) We don't expose the volume control to e.g. pulseaudio anyways so it
is not useful
While at it also move the "HPO MIX DAC1" and "HPO MIX HPVOL" entries up a
bit so that they are no longer inbetween the "HPO L Playback Switch" and
"HPO R Playback Switch" entries.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Wed, 8 Aug 2018 09:05:31 +0000 (11:05 +0200)]
conf/ucm: bytcr-rt5645: Use the generic bytcr/PlatformEnableSeq.conf
Use the generic Intel SSP bytcr/PlatformEnableSeq.conf file, it is
identical to all the cset statements this commit removes.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Urja Rannikko [Wed, 6 Jun 2018 17:52:42 +0000 (17:52 +0000)]
conf/ucm: VEYRON-I2S: Add internal speakers and mic, other fixes
Other fixes include output/input names (comments) for UIs (pavucontrol)
to display, and Playback/CapturePCM entries so pulseaudio initializes
correctly on this hardware.
Signed-off-by: Urja Rannikko <urjaman@gmail.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Thu, 31 May 2018 15:10:26 +0000 (17:10 +0200)]
conf/ucm: chtnau8824: Add Cube iWork8 Air and Pipo W2S specific profiles
The Cube iWork8 Air and Pipo W2S tablets both only have a single speaker.
Add long-name profiles for them which are identical to the default
chtnau8824 profile, except that they include the nau8824/MonoSpeaker.conf
snippet instead of the nau8824/Speaker.conf one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Hans de Goede [Thu, 31 May 2018 15:10:25 +0000 (17:10 +0200)]
conf/ucm: chtnau8824: Add UCM profile for chtnau8824 boards
Add UCM profile for chtnau8824 boards based on:
https://github.com/plbossart/UCM/blob/master/chtnau8824
Split into multiple files in the same way as this was done for the
bytcr-rt5640 support, re-using the existing ucm/PlatformEnableSeq.conf
and ucm/PlatformDisableSeq.conf files for the SST mixer settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a disable sequence powering off the SST mixer elements, loosely
based on the default DisableSequence from:
https://github.com/plbossart/UCM/blob/master/chtnau8824/HiFi.conf
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
With a recently merged kernel commit, the kernel now sets a long-name for
bytcr-rt5640 boards which indicates if a single (mono) speaker or stereo
speakers are used and wether dmic1, in1 or in3 is used for the internal
mic (the headset mic sofar is always in2).
This commit adds UCM profiles for bytcr-rt5640 boards using these new
long-names, based on the generic bytcr-rt5640 profile.
The added profiles have the unnecessary input / output options from the
generic profile removed leaving only 2 input and 2 output options, which
are automatically switched between by e.g. pulse based on jack-detect.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This commit adds the generic UCM profile for bytcr-rt5640 boards from:
https://github.com/plbossart/UCM, plus the fixes from this pull-req:
https://github.com/plbossart/UCM/pull/31
The profile has been split up into separate per input / output files to
allow for creation of long-name profiles with the specific input / output
combinations found on a board without needing to copy and paste things.
Note this profile exports all inputs and both stereo/mono speaker setups
even though a typical device will not use all. Ideally a long-name based
device specific profile made up of the various parts should be used
instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai [Wed, 2 May 2018 14:23:21 +0000 (16:23 +0200)]
conf/ucm: Add a UCM profile for Dell WD15 Dock USB-audio
USB-audio device on Dell WD15 docking station provides two individual
PCM streams, one for headphone and another for line out. A UCM
profile gives the proper roles for these.
Hans de Goede [Sat, 28 Apr 2018 19:52:00 +0000 (21:52 +0200)]
conf/ucm: chtrt5645: At config for the Lenovo Ideapad Miix 320
The Lenovo Ideapad Miix 320 uses a digital mic connected to the DMIC2 input
(unlike the Asus T100HA which has it connected to the DMIC1 input), add a
long-name config specific for the Miix 320, which is a copy of the standard
chtrt5645 config with the internal analog mic section replaced with one
for a digital mic connected to the DMIC2 input.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hans de Goede [Sat, 28 Apr 2018 19:51:59 +0000 (21:51 +0200)]
conf/ucm: chtrt5645: At config for the Asus T100HA
The Asus T100HA uses a digital mic rather then an analog one, add
long-name config specific for the T100HA, which is a copy of the standard
chtrt5645 config with the internal analog mic section replaced with one
for the digital mic found on the Asus T100HA.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a configuration for Cherry Trail boards which use a rt5645 codec
connected to a mono speaker and with an analog mic on IN2N + IN2P.
The chtrt5645-mono-speaker-analog-mic/HiFi.conf for this is based on the
latest version from https://github.com/plbossart/UCM/tree/master/chtrt5645
with all the unused input options removed and some changes made to make
the analog mic work.
This commit also adds 2 ucm dirs with the longname of 2 boards known to use
this setup, which simply contain a symlink to the generic
chtrt5645-mono-speaker-analog-mic entry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 5 Dec 2017 14:08:01 +0000 (15:08 +0100)]
conf/ucm: Add Gigabyte mobo UCM profile with dual HD-audio codecs
Like the previous Lenovo laptops, some Gigabyte mobos have dual
HD-audio codecs and need to switch dynamically via UCM profile.
Reuse the same profile as Lenovo dual codecs, so far.
Takashi Iwai [Tue, 5 Dec 2017 13:53:11 +0000 (14:53 +0100)]
conf/ucm: Add dual HD-audio codecs config for Lenovo
Some recent Lenovo laptops have dual codecs and we need to switch them
accordingly. The kernel side already contains a fix and gives the
unique longname string for identifying the board, and here we hook up
the corresponding UCM profile.
The profile was corrected and tested by Hui Wang on Lenovo p520.
Carlo Caione [Wed, 8 Nov 2017 12:33:30 +0000 (12:33 +0000)]
conf/ucm: rt5651: Mute speakers on boot
The UCM configuration is enabling the speakers in the SectionDefaults.
This is a problem when booting with an headset already connected since
the audio output is routed at the same time both on speakers and
heaphones until the jack is disconnected and reconnected again.
Fix this disabling all the outputs in the default mixer configuration.
Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
git://git.alsa-project.org / alsa-ucm-conf.git / log